HP210A-25KW-HD

High power detector for laser power measurement up to 25000 W.

Aperture

There is no product match with this configuration.
Please change the value for cooling and/or absorber.
- 60 mm Ø (Optimized for 35 mm Ø)
- 70 mm Ø
- 100 mm Ø
- 125 x 125 mm
- 210 x 210 mm
- 280 x 280 mm
Absorber
- GD - High power density
- HD - Broadband, high power
- HE - Broadband, high power
Cooling fittings
- Metric
- Imperial
Output
- Standard + USB
- INTEGRA (USB)
- INTEGRA (RS-232)
- INTEGRA (USB with external trigger)
- BLU (wireless)

Key features

The Highest Power Handling

Custom models handle up to 100 000 W of continuous power. Higher powers are available upon request.

Stable Reading

Less sensitive to variations in water cooling temperature than any other high power watercooled meter on the market.

Infinite Customization Capabilities

Choose your size
Choose your maximum power
We will customize one just for you!

Compact and Light Weight

Lighter and more compact than any other high power detector on the market, thanks to our unique design.

Available with YAG and CO₂ Calibration

All HP models can be calibrated at YAG and CO₂ wavelengths with a calibration uncertainty of +/- 5%.

Direct USB Connection to a PC

Each head comes with both a DB-15 connector (for use with a Gentec-EO monitor) and a USB2.0 output for direct connection to a PC. Other connectors available upon request.

Compatible displays & PC interfaces

MAESTRO

Touchscreen display device for power & energy measurement. Single-channel, multiple outputs (USB, Ethernet, Analog).
TUNER

Display device with tuning needle for power measurement. Single-channel.
UNO

Economical display device for power measurement. Single-channel.
S-LINK-1

PC interface for power & energy measurement. Single-channel, USB output.
S-LINK-2

PC interface for power & energy measurement. Dual-channel, USB output.
P-LINK (USB)

PC interface for power measurement. Single-channel, USB output.
M-LINK

PC interface for power & energy measurement. Single-channel, USB output.
P-LINK (RS-232)

PC interface for power measurement. Single-channel, RS-232 output.
P-LINK-4 (USB)

PC interface for power measurement. Four channels.
P-LINK-4 (Ethernet) V2

PC interface for power measurement. Four channels.
S-LINK-1 (Ethernet)

PC interface for power & energy measurement. Single-channel, USB & Ethernet output.
S-LINK-2 (Ethernet)

PC interface for power & energy measurement. Dual-channel, USB & Ethernet output.

Measurement capabilities

Maximum average power (continuous)
25000 W
Minimum average power¹
500 W
Noise equivalent power²
20 W
Spectral range
0.19 - 20 μm
Typical rise time
25 sec
Typical power sensitivity
0.08 mV/W
Power calibration uncertainty
±5 %
Repeatability
±2 %
Linearity with power
±2 %
Linearity vs beam diameter
±2 %
Maximum divergence
- 1. For lower powers, call your Gentec-EO representative.
- 2. Nominal value. Actual value depends on electrical noise in the measurement system.

Water requirements

Required cooling flow¹
(12 - 15) LPM < ±1 LPM/min
Temperature range
15 – 25 °C
Rate of temperature change
< ±3°C/min
- 1. Contact Gentec-EO for clean deionized water cooling module option.

Damage thresholds

Maximum average power density¹
2.5 kW/cm²
- 1. At 1064 nm, 1.07-1.08 µm and 10.6 µm.

Controller and GUI specifications

Data display
Real time, scope, needle, averaging, histogram and statistics
Analog output¹
0-2 Volts
Serial commands via
USB
External power supply²
Through USB or Gentec-EO displays & PC interfaces
Display type
None
- 1. 12 V maximum output signal available upon request.
- 2. A USB power adaptor will be necessary if the HP is used with a DB-15 extension cable.