HP100A-12KW-HD-TUBE

P/N 202687M

High power detector for laser power measurement up to 12000 W. Includes extension tube to reduce back reflections.

Aperture

There is no product match with this configuration.
Please change the value for cooling and/or absorber.
- QBH
- 60 mm Ø
- 100 mm Ø
- 250 mm Ø
- 125 x 125 mm
- 280 x 280 mm
- 500 x 500 mm
Absorber
- HE - 広帯域、高出力
- HD - 広帯域、高出力
- GD - 高出力密度、大きなコーン
- GD - 高出力密度、小さなコーン
Back reflections
- デフォルト（TUBEなし）
- 低（TUBEあり）
Fittings
- メートル
- インペリアル
Output
- Standard (DB15) + USB
- BLU（DB15 + ワイヤレス）

トレーサブル較正

Product family key features

High Power Handling

Handles up to 30 kW of continuous power with our standard models. Custom models are available for higher powers (See SUPER HP).

Stable Reading

Less sensitive to variations in water cooling temperature than any other high-power water-cooled meter on the market

Large Aperture

Our standard HP models (4KW, 12KW, 15KW and 30KW) have a very large effective aperture of up to 280 mm to accommodate even the largest laser beams. Larger apertures with various shapes are available upon request (See SUPER HP).

Available with YAG and CO₂ Calibration

All HP Models can be calibrated at YAG and CO₂ wavelengths with a calibration uncertainty of +/- 5%

Direct USB Connection to a PC

Each head comes with both a DB-15 connector (for use with a Gentec-EO monitor) and a USB2.0 output for direct connection to a PC.

Compatible stand

STAND-S-443-C

Compatible displays & PC interfaces

MAESTRO

Touchscreen display device for power & energy measurement. Single-channel, multiple outputs (USB, Ethernet, analog).
TUNER

Display device with tuning needle for power measurement. Single-channel.
UNO

Economical display device for power measurement. Single-channel.

含まれるもの

Calibration

Calibration certificate
CASE

Transport case
PWC

Personal wavelength correction^TM Certificate
COVER

Protective cover for optical surfaces
HP-W-ADAPTOR-3/8-10mm

Adaptor for water fittings of HP series. Changes the thread from imperial (3/8") to metric (10 mm OD). One unit of this item corresponds to two of the described tubes.

Print specifications

Measurement capabilities

Maximum average power (continuous)
12000 W
Minimum average power¹
300 W
Noise equivalent power²
10 W
Spectral range
0.193 - 20 μm
Typical rise time
9 s
Typical power sensitivity
0.15 mV/W
Power calibration uncertainty
±5 %
Repeatability
±2 %
Back reflections
< 4 %
Linearity with power
±1.5 %
Linearity vs beam diameter
±1 %
Linearity vs beam position³
±1.7 %
- 1. For lower powers, call your Gentec-EO representative.
- 2. Nominal value. Actual value depends on electrical noise in the measurement system.
- 3. For a beam size of 20% of the aperture area, moved across 80% of the aperture area.

Water requirements

Required cooling flow¹
(6 - 10) LPM < ±1 LPM/min
Temperature range
15 – 25 °C
Rate of temperature change
< ±3°C/min
Maximum water pressure
413 kPa (60 psi)
- 1. Contact Gentec-EO for clean deionized water cooling module option.

Damage thresholds

Maximum average power density¹
16 kW/cm²
- 1. At 1064 nm, 1.07-1.08 µm and 10.6 µm, 500 W CW. Refer to user manual for damage threshold at other powers. May vary with wavelength and average power.

Controller and GUI specifications

Data display
Real time, scope, needle, averaging, histogram and statistics
Analog output¹
0-2 Volts
Serial commands via
USB
External power supply²
Through USB or Gentec-EO displays & PC interfaces
Display type
None
- 1. 12 V maximum output signal available upon request.
- 2. A USB power adaptor will be necessary if the HP is used with a DB-15 extension cable.