EN

HP100A-12KW-HD-TUBE-IMP-D0

P/N 202687I

High power detector for laser power measurement up to 12000 W. Includes extension tube to reduce back reflections.

    • QBH
    • 60 mm Ø
    • 100 mm Ø
    • 250 mm Ø
    • 125 x 125 mm
    • 280 x 280 mm
    • 500 x 500 mm
    • HE - Broadband, high power
    • HD - Broadband, high power
    • GD - High power density, large cone
    • GD - High power density, small cone
    • Standard (without TUBE)
    • Low (with TUBE)
    • Imperial
    • Metric
    • Standard (DB15) + USB
    • BLU (DB15 + wireless)
HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0 HP100A-12KW-HD-TUBE-IMP-D0

Key features

High Power Handling

Handles up to 15 kW of continuous power with our standard models. Custom models available for higher powers (See SUPER HP).

Stable Reading

Less sensitive to variations in water cooling temperature than any other high power water-cooled meter on the market

Large Aperture

Our standard HP models (4KW, 12KW and 15KW) have a very large effective aperture up to 125 mm Ø to accomodate even the largest laser beams. Larger apertures with various shapes are available upon request (See SUPER HP).

Available with YAG and CO2 Calibration

All HP Models can be calibrated at YAG and CO2 wavelengths with a calibration uncertainty of +/- 5%

Direct USB Connection to a PC

Each head comes with both a DB-15 connector (for use with a Gentec-EO monitor) and a USB2.0 output for direct connection to a PC.

Award-winning technology

The HP-BLU series wireless detectors for high-power lasers was recognized among the best by an esteemed and experienced panel of judges from the optics and photonics community at the 2020 Laser Focus World Innovators Awards. 


Compatible stand

Compatible displays & PC interfaces

  • MAESTRO MAESTRO

    Touchscreen display device for power & energy measurement. Single-channel, multiple outputs (USB, Ethernet, analog).

  • BLU BLU

    Embedded wireless interface for power measurement. Can only be purchased as a detector output option.

  • TUNER TUNER

    Display device with tuning needle for power measurement. Single-channel.

  • UNO UNO

    Economical display device for power measurement. Single-channel.

Measurement capabilities

  • Maximum average power (continuous)

    12000 W

  • Minimum average power1

    300 W

  • Noise equivalent power2

    10 W

  • Spectral range

    0.193 - 20 μm

  • Typical rise time

    9 s

  • Typical power sensitivity

    0.15 mV/W

  • Power calibration uncertainty

    ±5 %

  • Repeatability

    ±2 %

  • Back reflections

    < 4 %

  • Linearity with power

    ±1.5 %

  • Linearity vs beam diameter

    ±1 %

  • Linearity vs beam position3

    ±1.7 %
    • 1. For lower powers, call your Gentec-EO representative.
    • 2. Nominal value. Actual value depends on electrical noise in the measurement system.
    • 3. For a beam size of 20% of the aperture area, moved across 80% of the aperture area.

Water requirements

  • Required cooling flow1

    (6 - 10) LPM < ±1 LPM/min

  • Temperature range

    15 – 25 °C

  • Rate of temperature change

    < ±3°C/min

  • Maximum water pressure

    413 kPa (60 psi)
    • 1. Contact Gentec-EO for clean deionized water cooling module option.

Damage thresholds

  • Maximum average power density1

    16 kW/cm²
    • 1. At 1064 nm, 1.07-1.08 µm and 10.6 µm, 500 W CW. Refer to user manual for damage threshold at other powers. May vary with wavelength and average power.

Controller and GUI specifications

  • Data display

    Real time, scope, needle, averaging, histogram and statistics

  • Analog output1

    0-2 Volts

  • Serial commands via

    USB

  • External power supply2

    Through USB or Gentec-EO displays & PC interfaces

  • Display type

    None
    • 1. 12 V maximum output signal available upon request.
    • 2. A USB power adaptor will be necessary if the HP is used with a DB-15 extension cable.

Physical characteristics

  • Aperture diameter

    70 mm

  • Absorber

    HD

  • Dimensions

    127H x 127W x 230D mm

  • Weight

    7.5 kg
Print specifications
Get a quote
Customize this product Inquire

AWARD-WINNING TECHNOLOGY

The HP-BLU series wireless detectors for high-power lasers was recognized among the best by an esteemed and experienced panel of judges from the optics and photonics community at the 2020 Laser Focus World Innovators Awards. 

High power measurements in enclosures or hard-to-reach areas are no longer a problem with the BLU wireless output. With the BLU option, you can grab your laser measurement data at up to 30 m distance with your PC.

Related videos

Compatible products you may need

Your item has been added to your cart!

You might need these specific products to be able to use the placeholder only.

Compatible products

No compatible product

Check if this product works for your laser

Measurement type:

1

Beam size

2

Laser type

3

Beam profile

COPYRIGHT ©2022 Gentec-eo Spektrum média